: Digitech RP14D Amp Modeling Effects Processor – “Real Tube Amp Modeling, powered by a high voltage 12AX7 tube. The RP14D has 10 . Hello!Up for sale is a very amazing multi-effects unit by nice tube driven preamp / floor board multi-effects processor! Nice sounding tube. Tested and working – used condition – see pics – includes power supply. Ships free via importantly – please read the 4 Gospels 4 2 The.
|Published (Last):||7 October 2013|
|PDF File Size:||16.84 Mb|
|ePub File Size:||16.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
The foregoing is in lieu of all other warranties, expressed or implied, and Digitech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall Digitech or its rp41d be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
The simple user interface lets you quickly create Programs and assign functions to the built in expression pedal. Turn the Output knob on the front panel of the RP14D all the way down fully counter clockwise.
Connect the other end of the PS power supply to an AC outlet. Turn the digitrch of rp1d4 amplifier s to the on position and adjust the volume s. Down Parameter buttons are used to select the Parameter of the selected Digiyech.
Simply follow the horizontal and vertical LEDs across the Matrix to the point where they intersect. This will be the parameter you are about to edit. Use only the DigiTech PS power supply provided. The signal at this output is in a digital format, and is to be connected to a Before connecting the RP14D, make sure that the power to your amplifier is turned off, and that the power to the RP14D is disconnected.
There is no power r;14d on the RP14D. Once the audio connections have been made, turn the Output Level all the way down counterclockwise. Connect the 4 pin connector of the power adapter to the power jack on the back of the RP14D and the other end to an AC outlet.
User reviews: DigiTech RP14D – Audiofanzine
Turn the power to your amplifier s on. Set the amp s to a clean tone setting and set the tone controls to a flat EQ response on most amps, this would be 0 or 5 on the tone controls.
As you go through the different Programs that came in the RP14D, you will find that the expression pedal has different functions. This pedal can be assigned to control any one of 13 different parameters in the RP14D.
Rocking the pedal back and forth will change the value of the parameter that the pedal has been assigned to control. Once a Figitech has been edited to your liking, you may store those settings to any of the 50 User Program locations. Remember that the User Programs are duplicates of the Factory Programs so, you are not at risk of losing any of the sounds that the RP14D came with.
Digitech – RP14D amp modelling fx processors
When editing a Program, the Store LED will light indicating that you have changed a Parameter and need to store the changes. The following steps outline the proce- dure for storing a dp14d The Parameters are arranged in horizontal rows and the Effects are in vertical columns. Use the Parameter Select keys to navigate the matrix. The Effects and their Parameters are as follows Display will show Off, or one of the Parameter abbreviations. The Parameters and their abbreviations available for Expression control in the RP14D are listed below.
Use the Value Up or Down buttons to select the Parameter you wish to control. You can then set minimum and maximum values which are stop points for the top and bottom positions on the Expression Pedal. The Amp Model Effect occupies two columns on the Matrix. It fp14d at the strength of diitech incoming signal and if the sig- nal exceeds the value set by the Threshold parameter, the gate will open and allow the signal to pass. If rigitech signal level drops below the Threshold, the gate will close and allow nothing through until the Threshold is exceeded again.
A Chorus adds a short delay to your signal and modulates the delay time which takes the delayed signal slightly in and out of tune. The delayed signal is then digotech back with the original signal to create a thicker texture as if two guitars were playing the same part. A phaser splits the incoming signal, and then changes the phasing of rp14c signal. This signal is then taken in and out of phase and mixed back in with the original signal.
As you play one note the pitch shifter is simultaneously playing a note higher, or lower with you. The RP14D is capable of shifting the signal from 0 to 24 semi-tones 2 octaves above or below the pitch of the input signal.
The difference between a Pitch Shifter and an intelligent Pitch Shifter is that the Pitch Shifter stays parallel to your note at the specified interval, and an intelligent Pitch Shifter knows which notes dugitech make sharp or flat in order to keep the shifted pitches diggitech the specified key and scale. It combines the characteristics of a wah and a flanger together providing a unique talk box type of dogitech.
The YaYa vigitech are as follow: Amount Determines the quantity of sweep in the YaYa effect. This type of effect is also referred to as an echo because it basically echoes the original signal. Delay Parameters are as follows: Determines the type of delay. This maintains the integrity of your signal. No miking hassles, no heavy equip- ment, just full on miked cabinet sound. The fol- lowing steps will guide you through the procedure for creating just such a Program in the RP14D.
Amp Gain When you select a particular amp type in the Model section of the RP14D, the EQ settings automatically default to give you the settings of the selected ep14d type. Rp114d you can boost or cut these to suit your taste and in our example Program we wanted some heavy bass.
Press the Parameter Down button again and by following the grid across you will find that this is the Bass Parameter. Store the Program The last step that we need to do is to store our changes to a User Program. If we changed Programs or turned the RP14D off without storing these settings, it would forget what we had done and revert back to the original Program. Press the Store button once. A U begins flashing in the Display, which is asking us to select the User Bank and Program number that we wish to save our changes to.
The RP14D will reset to factory condition. International Distribution S. Page of 35 Go. Table of Contents Add to my manuals Add. Modeling guitar processor and usb audio interface 48 pages. R14d generates bass and drum parts that match your song 63 pages. Declaration Of Conformity S.
DigiTech RP14D Integrated Tube Guitar Processor Multi-effect Pedal
Table Of Contents Included Items The Rear Panel 6. Getting Started Before connecting the RP14D, make sure that the power to your amplifier is turned off, and that the power to the RP14D is disconnected. The Footswitches As you go through the different Programs that came in the RP14D, you will find that the expression pedal has different functions.
Section Two – Editing Functions Once a Program has been edited to your liking, you may store those settings to any of the 50 User Program locations. Expression Pedal Display will show Off, or one of the Parameter abbreviations.
Auto Ya This type of effect is also referred to as an echo because it basically echoes the original signal.
Section Five – Appendix 1. Page 35 International Distribution S. Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Dibitech it, continue to print. Don’t have an account?