HT12D DATASHEET IN PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. HT12D Datasheet, HT12D Holtek Decoder Datasheet, buy HT12D Decoder IC.

Author: Zolosho Kagrel
Country: Albania
Language: English (Spanish)
Genre: Sex
Published (Last): 10 January 2009
Pages: 271
PDF File Size: 15.21 Mb
ePub File Size: 1.78 Mb
ISBN: 561-8-58710-722-5
Downloads: 15602
Price: Free* [*Free Regsitration Required]
Uploader: Gakasa

These two ICs together form an Encoder and Decoder pair. Connected to the Ground of circuit.

Skip to main content. In simple terms, HT12D converts the serial input into parallel outputs. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. It is not mandatory eatasheet use it.

This pin will go high when a data is received. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. ht112d

HT12D/HT12F – Product Details – Holtek

Submitted by admin on 27 October They are paired dwtasheet 2 12 series of encoders. The data on 4 bit latch type output pins remain unchanged until new is received.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. Interface SD Card with Arduino. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received.

  AVTECH KPD 679 PDF

The 4-bit data that dagasheet received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. Virgin Galactic — Commercial Space Flight. Choosing Battery for Robots. ratasheet

TL — Programmable Reference Voltage. It is very important that your Decoder should have the same address of that of the encoder.

If you want security you can connect any of the 8 pins to 5V to make it high. We should set the bits in same pattern on Encoder and Decoder IC to pair them. The input data code is decoded when no error or unmatched codes are found. If any valid data is received they can be obtained from these four pins.

It is mainly provided to interface RF and infrared circuits. Supply voltage; 5V 2. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. Arduino based GPS receiver. A valid transmission in indicated by a high signal at VT pin.

This high-density Datashest SiP integrates controller, power switches, and support components.

It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. What is Web Browser. These are the 8-bit address bits, which is used to protect your data.

  DENBIGH THE PRINCIPLES OF CHEMICAL EQUILIBRIUM PDF

The IC has a built in oscillator.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address datashheet to ground. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. Valid transmission; active high. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Interface GPS with Arduino. This oscillator can be used by connecting these two pins through a 1M Resistor. They can also be connected to LED to physically view the received data.

HT12D Decoder IC

A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set datasheeh 8-bit address data as 0b, by connecting all address pins to ground.

The Encoded 12 bit output data obtained from HT12E has to be given here. SPI Module of Arduino. This pin powers the IC should use only 5V. Choosing Motor For Robots. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

The serial input data is compared with the local addresses three times continuously.